Enmienda 1 al IPC-7711/21C, el documento proporciona los procedimientos para la extracción y la instalación de componentes D-Pak.
Products
IPC-7711/21C的修订本1，本文件提供D-Pak元器件的去除和安装程序.
Amendement 1 à IPC-7711 / 21C fournit des procédures supplémentaires de retrait et d'installation
IPC/WHMA-A-620C-S provides additional requirements to IPC/WHMA-A-620C to ensure the reliability of cable and wire harness assemblies that must survive the vibration and thermal cyclic environments getting to and operating in space. The IPC/WHMA-A-620C-S space addendum cannot be used as a stand alone document, it must be used with the base standard IPC/WHMA-A-620C.
When specifically required by procurement documentation, this Addendum supplements or replaces specifically identified requirements of IPC/WHMA-A-620, Revision B, providing additional requirements to ensure the reliability of cable and wire harness assemblies that must survive the vibration and thermal cyclic environments getting to and operating in space. The required IPC training & certification...
IPC/WHMA-A-620AS with Amendment 1 Space Applications Electronic Hardware Addendum to IPC/WHMA-A-620A Requirements and Acceptance for Cable and Wire Harness Assemblies. When specifically required by procurement documentation, this Addendum supplements or replaces specifically identified requirements of IPC/WHMA-A-620, Revision A of July 2006 by providing additional requirements to ensure the...
This Addendum supplements or replaces specifically identified requirements of IPC-6018C, for high frequency (microwave) printed boards that must survive the vibration, ground testing and thermal cyclic environments of space and military avionics.
This standard on spherical transient bend testing is intended to characterize the maximum allowable strain that a surface mount component's board level interconnects can withstand in flexural loading. Whereas four-point monotonic bend test methods only address simple planar bending, spherical bend tests establish strain limits of board level interconnects under worst-case flexure conditions that...
IPC-HDBK-9798 provides guidelines and supporting information for manufacturing electronic assemblies using compliant press-fit technology. The intent is to explain the ‘‘how-to’’ and ‘‘why’’ information, and fundamentals for these processes. This handbook is supporting the IPC-9797 standard.
IPC-9797 is the only industry-consensus standard for Requirements and Acceptance of Press-fit Pins. IPC-9797 prescribes practices for the characterization, qualification and acceptance requirements of compliant press-fit technology for printed boards that cover the manufacturability and reliability needs for high reliability applications intended for use in harsh environments such as automotive...
IPC-9191 reflects the principals of statistical process control (SPC) represented by ISO/DIS 11462-1, Guidelines for Implementation of Statistical Process Control (SPC) -- Part 1: Elements of SPC. This document outlines the SPC philosophy, implementation strategies, tools, and techniques used for relating process control and capability to final product requirements. Supersedes IPC-PC-90.
This standard describes the methods of inspecting and cleaning all optical interfaces so that interconnectivity integrity of the optical signal is maintained. The information provided focuses on techniques and methods to accomplish maximum quality of the interface and describes methods of contamination prevention. The target audience for this standard are Manufacturing Operators, Manufacturing...
Discusses the many variables and problems associated with the process--from sample removal to micro-etch-- and the variables common to high volume microsection. The process variables and problems are organized so that the reader can research a specific issue or overview the variables of a process area. 31 pages. Released October 1993.
IPC-9631 addresses concerns and considerations related to IPC-TM-650, Method 2.6.27, Thermal Stress, Convection Reflow Assembly Simulation. This document describes how the test method is intended for use and the rationale behind some of the protocols and requirements. This document was developed with the understanding that the test method will require special equipment and the proper set-up and...
Establishes mechanical drop and shock and test guidelines for assessing solder joint reliability of printed board assemblies from system to component level. This document addresses methods to define mechanical shock use-conditions, methods to define system level, system printed board level and component test board level testing that correlate to such use conditions and guidance on the use of...
This guideline standard is intended to aid in interpretation of the requirements in IPC-9191, "General Guidelines for Implementation of Statistical process Control," specifically for printed board assembly (PBA) manufacture. This document and IPC-9191 should be used together; the standards are cross-referenced to each other in the Appendices of this guideline. This standard promotes process...
During mass soldering, it is important that all solder joints reach the minimum soldering (reflow) temperature to assure metallurgical bonding of the solder alloy and the base metals to be soldered. Metallurgical bonding requires that both surfaces to be soldered, as well as the solder, reach this minimum soldering temperature for a sufficient time to allow the wetting of the solder surfaces. This...
Implementing flip chip technology in a direct chip attach (DCA) assembly presents some unique challenges for design, assembly, inspection and repair personnel. IPC-7094 delivers useful and practical information to anyone who is currently using or contemplating developing products that employ the very complex and high density methods needed for the flip chip technology. The concepts have become...
Guidelines for accelerated reliability testing of surface mount solder attachments when evaluating and extrapolating the results of these tests towards actual use environments of electronic assemblies. 50 pages. Released November 1992. Included in the IPC-C-103 and the IPC-C-1000 Collections
This standard establishes mechanical outline requirements for devices supplied in flip chip or Chip Size Package (CSP) formats, including die surface, die terminals, and interconnection balls/bumps/lands to the next level. 13 Pages. Released February 2003.
This test method defines the procedures for performing acoustic microscopy on non-hermetic encapsulated electronic components. It provides users with an acoustic microscopy process flow for detecting defects non-destructively in plastic packages while achieving reproducibility. Developed by IPC and JEDEC. 16 pages. Released April 1999. Equivalent to IEC Publicly Available Specification (PAS) 62191
IPC/WHMA-A-620E-RL is a redline document showing the difference from IPC/WHMA-A-620D to IPC/WHMA-A-620E. IPC/WHMA-A-620E-RL provides a side-by-side comparison of the two documents and includes the figures and tables. The document shows deleted/changed text in the IPC/WHMA-A-620D pages and new/revised text in the IPC/WHMA-A-620E pages. Due to the complexity of this document, it is only available in...
IPC-D-620 provides design and critical process requirements for the three product classes of cable and wire harness assemblies as well as military/space applications. It is the design requirements companion to IPC/WHMA-A-620, "Requirements and Acceptance for Cable and Wire Harness Assemblies," and its associated Space Addendum Three white papers are included to provide guidance on key topics...
This document provides tests that record changes in surface insulation resistance (SIR) on a representative sample of a printed circuit assembly. It quantifies any deleterious effects that might arise from solder flux or other process residues left on external surfaces after soldering, which can cause unwanted electrochemical reactions that grossly affect reliability. It uses test vehicles that...
Surface mount pad cratering typically initiates prior to detection by existing electrical monitoring test methods. There are limited instrumentation techniques that are currently available that can identify non-electrical damage and its location to a high degree of accuracy. This guideline document establishes an acoustic emission (AE) method to evaluate the performance and reliability of surface...
Coming Soon
IPC-9242: Guidelines for Microsection Evaluation
IPC-A-630A: Acceptability Standard for Manufacture, Inspection, and Testing of Electronic Enclosures
IPC-7527A: Requirements for Solder Paste Application
IPC-4204C: Flexible Metal-Clad Dielectrics for Use in Fabrication of Flexible Printed Boards
IPC-J-STD-002F: Solderability Tests for Component Leads, Terminations, Lugs, Terminals and Wires
IPC-4101F: Specifications for Base Materials for Rigid and Multilayer Printed Boards
IPC-1755B: Responsible Sourcing of Minerals Data Exchange Standard
IPC-2223F: Sectional Design Standard for Flexible/Rigid-Flexible Printed Boards
IPC-HDBK-9798A: Handbook and Guide to Supplement IPC-9797
IPC-WP-011: Guidance for Strain Gage Limits for Assemblies
J-STD-048A: Notification Standard for Product Discontinuance
IPC-T-50P: Terms and Definitions for Interconnecting and Packaging Electronic Circuits
IPC-1401B: Corporate Social Responsibility Management System Standard
IPC -1751B: Generic Requirements for Declaration Process Management
IPC-6013F: Qualification and Performance Specification for Flexible/Rigid-Flexible Printed Boards
IPC-4413 - Am1: Specification for Finished Fabric Woven from Low Dk Glass for Printed Boards