The IPC-4202C standard covers the requirements for flexible base materials, herein referred to as laminates, prepregs or films, to be used primarily for flexible printed boards for electrical and electronic circuits
Products
The IPC-9701B standard establishes a thermal cycling test method to characterize the fatigue lifetimes of surface mount solder attachments of electronic assemblies. The surface mount devices may be solder-attached to rigid, flexible or rigid-flex printed boards. The characterization results can be used to predict the field lifetime of solder attachments for the use environments and conditions of...
This standard provides a marking and labeling system that aids in assembly, rework, repair and recycling and provides for the identification of: 1. those assemblies that are assembled with lead-containing or lead-free solder; 2. components that have lead-containing or lead-free second level interconnect terminal finishes and materials; 3. the maximum component temperature not to be exceeded during...
The IPC-7801A standard provides requirements for process control of conveyorized solder reflow ovens. It includes a methodology for performing temperature measurements over time to establish a baseline profile, and then provides requirements to verify repeatability through periodic verification of the oven profile.
While there are a variety of industry test vehicles for the examination of material compatibility, the IPC-B-52 test board was created to meet the needs for testing both ion chromatograph and surface insulation resistance (SIR) which would be more representative of the manufacturing materials and processes. IPC-9203A standard addresses the IPC-B-52 test vehicle, which can be used to evaluate a...
IPC/JEDEC J-STD-035A test method defines the procedures for performing acoustic microscopy on nonhermetic encapsulated electronic devices. IPC/JEDEC J-STD-035A method provides users with an acoustic microscopy process flow for detecting anomalies (delaminations, cracks, mold compound voids, etc.) nondestructively in encapsulated electronic devices while achieving reproducibility
The IPC-1921A handbook provides problems, causes and possible corrective actions related to printed board manufacturing processes. Includes more than 200 photos and illustrations depicting common defects.
This standard provides and defines key characteristics and test methods for procuring printed electronics substrates. Includes six materials specification sheets.
The IPC-4591A standard establishes the classification system and the qualification and quality conformance requirements for functional conductive materials used in printed electronics applications. It provides companies that procure functional materials for printed electronics with the necessary technical structure to design and manufacture products meeting conformance to industry-determined...
The IPC-4412C covers the requirements for reinforcements woven from "E"glass yarn. These reinforcements are used in the production of prepregs, some of which are pressed into laminates. These prepregs and laminates are the base materials for rigid and mulitlayer printed boards. The IPC-4412C standard contains tables which describe each fabriic style in detail including the yarn used, the number of...
This document describes the design and assembly challenges and ways to address those challenges for implementing 3D component technology. Recognizing the effects of combining multiple uncased semiconductor die elements in a single-package format can impact individual component characteristics and can dictate suitable assembly methodology. The information contained in this standard focuses on...
The IPC-9202A, Material and Process Characterization/Qualification Test Protocol that records changes in Surface Insulation Resistance (SIR) on a representative sample of a printed circuit assembly (PCA). It quantifies any deleterious effects that might arise from solder flux or other process residues left on external surfaces after soldering, which can cause unwanted electro-chemical reactions...
The IPC-1401A standard specifies the requirements and best practice guidelines for an effective corporate social responsibility (CSR) management system to help an enterprise integrate CSR as a customer requirement into products and value chain activities, as well as to identify and manage CSR risks and opportunities through cooperation with customers and suppliers, to enhance the competitive...
The IPC-9709A standard guideline document establishes an Acoustic Emission (AE) method to enhance evaluation of the performance and reliability of surface mount attachments of electronic assemblies during mechanical loading.
The IPC-6017A standard defines the electrical, mechanical, and environmental requirements specific to embedded passive and active circuitry in printed boards. These requirements are in addition to the applicable requirements of other performance specification(s) (e.g., J-STD-001).
The IPC-1755A standard establishes the requirements for exchanging data between suppliers and their customers in regard to the responsible resourcing of minerals. The IPC-1755As standard originally addressed conflict minerals within the scope of the Dodd-Frank Act in the US. IPC-1755A expands the scope of this document to address global responsible minerals sourcing.
IPC-4203B establishes the classification system, the qualification and quality conformance requirements for dielectric films coated with an adhesive on one or both sides, which are to be used as cover material and/or bondply for flexible printed circuitry, as well as supported or unsupported adhesive films to be used in the fabrication of flexible printed circuitry. IPC-4203B does not cover non...
IPC-7094A describes the design and assembly challenges for implementing flip chip technology in a direct chip attach (DCA) assembly. The effect of bare-die or die-size components in a flip chip format has an impact on component characteristics and dictates the appropriate assembly methodology. The IPC-7094A standard focuses on design, assembly methodology, critical inspection, repair and...
IPC-4103B standard covers the requirements for clad and unclad plastic laminate and bonding layer materials to be used for the fabrication of printed boards for microstrip, stripline and high speed digital electrical and electronic circuits. In addition to better definitions of inclusions and how to properly classify them; redefine "substrates" as, "fabricated sheets"; and a more proper definition...
This is the document all process engineers must have! Useful for day-to-day problem solving, it contains case histories of problems and corrective action in the design, manufacture, assembly and testing of printed wiring products. Each section has been updated to reflect today's manufacturing challenges. Sections address documentation, phototooling, raw materials, mechanical operations, hole...
Provides requirements for dielectric adhesives to hold components in place from the mounting to the soldering process and identifies test methods to ensure their long term properties. 9 pages. Released December 2014.
This guideline describes flexibility and stretchability testing to evaluate printable electronics for stretchable and wearable applications. 26 pages. Released March 2017
This document is the product of the IPC Electrochemical Migration (ECM) Task Group. It was drafted to provide guidance regarding implementation of the User Guide for the IPC-TM-650, Method 2.6.25, Conductive Anodic Filament (CAF) Resistance and Other Internal Electrochemical Migration Testing to evaluate the effects of mechanical stress, laminate material fracturing, ionic contamination, moisture...
The IPC-6903A standard provides 62 additional terms and definitions for the design and manufacture of printed electronics. The IPC-6903A standard creates a common language and understanding for the worldwide printed electronics community.
Covers the nomenclature, definitions and requirements for reinforcement made from nonwoven para-aramid fibers. Para-aramid reinforcement is primarily used in PCBs for HDI and high speed/high frequency applications. IPC-4411A also includes specification sheets, which can be used when selecting and purchasing nonwoven para-aramid reinforcement. Includes the incorporation of 14 new nonwoven para...
Coming Soon
IPC-9242: Guidelines for Microsection Evaluation
IPC-A-630A: Acceptability Standard for Manufacture, Inspection, and Testing of Electronic Enclosures
IPC-7527A: Requirements for Solder Paste Application
IPC-4204C: Flexible Metal-Clad Dielectrics for Use in Fabrication of Flexible Printed Boards
IPC-J-STD-002F: Solderability Tests for Component Leads, Terminations, Lugs, Terminals and Wires
IPC-4101F: Specifications for Base Materials for Rigid and Multilayer Printed Boards
IPC-1755B: Responsible Sourcing of Minerals Data Exchange Standard
IPC-2223F: Sectional Design Standard for Flexible/Rigid-Flexible Printed Boards
IPC-HDBK-9798A: Handbook and Guide to Supplement IPC-9797
IPC-WP-011: Guidance for Strain Gage Limits for Assemblies
J-STD-048A: Notification Standard for Product Discontinuance
IPC-T-50P: Terms and Definitions for Interconnecting and Packaging Electronic Circuits
IPC-1401B: Corporate Social Responsibility Management System Standard
IPC -1751B: Generic Requirements for Declaration Process Management
IPC-6013F: Qualification and Performance Specification for Flexible/Rigid-Flexible Printed Boards
IPC-4413 - Am1: Specification for Finished Fabric Woven from Low Dk Glass for Printed Boards