Menu
Close
Contact Us

Standards

Your results

Document #

Language

Products

IPC-6018DS

IPC-6018 - Revision D - Addendum - Space and Military

Space and Military Avionics Applications Addendum to IPC-6018D, Qualification and Performance Specification for High Frequency (Microwave) Printed Boards

Document #:
IPC-6018
Revision
D
Product Type
Addendum
Released:  08/04/2022
Language
English
The IPC-6018DS addendum supplements or replaces specifically identified requirements of IPC-6018D, for high frequency (microwave) printed boards that must survive the vibration, ground testing and thermal cyclic environments of space and military avionics. The IPC-6018DS addendum incorporates new requirements in areas such as copper wrap plating, dewetting, pad/land anomalies, copper cap plating...

IPC-6012 - Revision E - Amendment 1

刚性印制板的鉴定及性能规范- 修订本1

Document #:
IPC-6012
Revision
E
Product Type
Amendment
Released:  10/28/2022
Language
Chinese
Current Revision
IPC-6012E-AM1是IPC-6012E的修订本，澄清了再流焊SnPb或HASL镀层中退润湿和焊料回缩之间的区别。 该修订本还为成品印制板的最小外部导体厚度提供了修订标准，并为内部电镀层的最小厚度提供了新的接受标准。

IPC-6012 - Revision D - Addendum - Automotive

Automotive Applications Addendum to IPC-6012D, Qualification and Performance Specification for Rigid Printed Boards

Document #:
IPC-6012
Revision
D
Product Type
Addendum
Released:  04/01/2016
Language
English
This Addendum, when required by procurement documentation/drawings, supplements or replaces specifically identified requirements of IPC-6012D, Revision D, for rigid printed boards that must survive the vibration and thermal cycling environments of electronic interconnects within the automotive industry.
no-image-available

IPC-6012 - Revision D - Amendment 1

Sert Baskı Devre Kartları İçin Kalifikasyon ve Performans Spesifikasyonu

Document #:
IPC-6012
Revision
D
Product Type
Amendment
Released:  01/25/2019
Language
Turkish
Current Revision
Bu döküman; kaplı delikiçine sahip olan veya olmayan tek yüzlü, çift yüzlü baskı devre kartları ve kör/gömülü geçiş deliklerine sahip olan veya olmayan çok katmanlı baskı devre kartları ile metal çekirdekli kartları içeren sert baskı devre kartlarının kalifikasyonunu ve performansını kapsamaktadır. Son kaplama ve yüzey kaplama gereklilikleri, iletkenler, delikler/geçiş delikleri, kabul testlerinin...

IPC-6012 - Revision D - Addendum - Space and Military

Space and Military Avionics Applications Addendum to IPC-6012D, Qualification and Performance Specification for Rigid Printed Boards

Document #:
IPC-6012
Revision
D
Product Type
Addendum
Released:  09/22/2015
Language
English
This Addendum supplements or replaces specifically identified requirements of IPC-6012D, Revision D, for rigid printed boards that must survive the vibration, ground testing and thermal cyclic environments of space and military avionics

IPC-6018 - Revision C - Addendum - Space and Military

Space and Military Avionics Applications Addendum to IPC-6018C Qualification and Performance Specification for High Frequency (Microwave) Printed Boards

Document #:
IPC-6018
Revision
C
Product Type
Addendum
Released:  08/09/2016
Language
English
This Addendum supplements or replaces specifically identified requirements of IPC-6018C, for high frequency (microwave) printed boards that must survive the vibration, ground testing and thermal cyclic environments of space and military avionics.

IPC-1602 - Standard Only

Standard for Printed Board Handling and Storage

Document #:
IPC-1602
Revision
Original Version
Product Type
Standard Only
Released:  04/07/2020
Language
English
The IPC-1602 standard provides requirements intended to protect printed boards from contamination, physical damage, solderability degradation and moisture uptake. Consideration is given to packaging materials types and methods, production environment, handling and transport of product, and establishing baking profiles for moisture removal. IPC-1602 is now providing requirements that can be called...

IPC-4552 - Standard with Amendment 1&2

Specification for Electroless Nickel/Immersion Gold (ENIG) Plating for Printed Circuit Boards

Document #:
IPC-4552
Revision
Original Version
Product Type
Standard with amendment(s)
Released:  06/26/2013
Language
English
In answer to numerous industry requests for guidance on electroless nickel/immersion gold (ENIG), IPC-4552 was developed. Containing full color photographs, this specification sets the requirements for the use of ENIG as a surface finish for printed boards. It includes requirements for ENIG deposit thicknesses based on performance criteria. It is an invaluable resource for use by suppliers, board...

IPC-4761 - Standard Only

Design Guide for Protection of Printed Board Via Structures

Document #:
IPC-4761
Revision
Original Version
Product Type
Standard Only
Released:  07/01/2006
Language
English
IPC-4761 is the sole industry guideline providing PCB designers, manufacturers and uses with detailed information on all existing methods for protecting vias on printed boards, including all types of via tenting, plugging, filling and capping. Production issues, long term reliability concerns and material specification and selection are provided to aid in evaluating the benefits and concerns for...

IPC-4821 - Standard Only

Specification for Embedded Passive Device Capacitor Materials for Rigid and Multilayer Printed Boards

Document #:
IPC-4821
Revision
Original Version
Product Type
Standard Only
Released:  05/01/2006
Language
English
This document describes materials that can be used for the fabrication of embedded passive capacitor devices within the finished printed circuit board substrate. For this document, embedded passive devices and the phrase embedded passives are considered to be equivalent. It provides information on general designations and associated characteristics of embedded passive device (EPD) capacitor...

IPC-9707 - Standard Only

Spherical Bend Test Method for Characterization of Board Level Interconnects

Document #:
IPC/JEDEC-9707
Revision
Original Version
Product Type
Standard Only
Released:  09/13/2011
Language
English
This standard on spherical transient bend testing is intended to characterize the maximum allowable strain that a surface mount component's board level interconnects can withstand in flexural loading. Whereas four-point monotonic bend test methods only address simple planar bending, spherical bend tests establish strain limits of board level interconnects under worst-case flexure conditions that...
no-image-available

IPC-4554 - Standard with Amendment

Specification for Immersion Tin Plating for Printed Circuit Boards

Document #:
IPC-4554
Revision
Original Version
Product Type
Standard with amendment(s)
Released:  08/10/2012
Language
English
IPC-4554, Specification for Immersion Tin Plating for Printed Circuit Boards, is included in the IPC-455X series of specifications that set the requirements for printed board surface finishes that are alternates to non-coplanar finishes, most often referred to as tin-lead HASL finish. This specification is a full-color document that is intended for use by the supplier or printed board fabricator...
no-image-available

IPC-SMEMA 3.1 - Standard Only

SMEMA3.1 - Fiducial Mark Standard

Document #:
IPC-SMEMA 3.1
Revision
Original Version
Product Type
Standard Only
Released:  02/12/2007
Language
English
This SMEMA standard is for fiducial marks. It was developed to facilitate the accurate placement of components on printed circuit boards.

IPC-4556 - Standard Only

Specification for Electroless Nickel/Electroless Palladium/Immersion Gold (ENEPIG) Plating for Printed Circuit Boards

Document #:
IPC-4556
Revision
Original Version
Product Type
Standard Only
Released:  02/05/2013
Language
English
This specification sets the requirements for the use of electroless nickel/electroless palladium/immersion gold (ENEPIG) as a surface finish for printed boards. It establishes requirements for ENEPIG deposit thicknesses for applications including soldering, wire bonding and as a contact finish. It is intended for use by chemical suppliers, printed board manufacturers, electronics manufacturing...
no-image-available

IPC-HDBK-9798 - Handbook

Handbook for Press-fit Standard for Automotive Requirements and other High-Reliability Applications

Document #:
IPC-HDBK-9798
Revision
Original Version
Product Type
Handbook
Released:  06/21/2022
Language
English
Current Revision
IPC-HDBK-9798 provides guidelines and supporting information for manufacturing electronic assemblies using compliant press-fit technology. The intent is to explain the ‘‘how-to’’ and ‘‘why’’ information, and fundamentals for these processes. This handbook is supporting the IPC-9797 standard.

IPC-6011 - Standard Only

Generic Performance Specification for Printed Boards

Document #:
IPC-6011
Revision
Original Version
Product Type
Standard Only
Released:  07/01/1996
Language
English
This specification establishes the general requirements and responsibilities for suppliers and users of printed boards. Serving as the foundation for the IPC-6010 Board Performance Documents series, it describes quality and reliability assurance requirements that must be met. For use with IPC-6012 through IPC-6018. Supersedes IPC-RB-276, IPC-SC-320, IPC-TC-500, IPC-ML-950C. 15 pages. Released July...

IPC-9797 - Standard Only

Press-fit Standard for Automotive Requirements and other High-Reliability Applications

Document #:
IPC-9797
Revision
Original Version
Product Type
Standard Only
Released:  06/01/2020
Language
English
IPC-9797 is the only industry-consensus standard for Requirements and Acceptance of Press-fit Pins. IPC-9797 prescribes practices for the characterization, qualification and acceptance requirements of compliant press-fit technology for printed boards that cover the manufacturability and reliability needs for high reliability applications intended for use in harsh environments such as automotive...

IPC-9191 - Standard Only

General Guidelines for Implementation of Statistical Process Control (SPC)

Document #:
IPC-9191
Revision
Original Version
Product Type
Standard Only
Released:  11/01/1999
Language
English
IPC-9191 reflects the principals of statistical process control (SPC) represented by ISO/DIS 11462-1, Guidelines for Implementation of Statistical Process Control (SPC) -- Part 1: Elements of SPC. This document outlines the SPC philosophy, implementation strategies, tools, and techniques used for relating process control and capability to final product requirements. Supersedes IPC-PC-90.
326-350 of 491

Coming Soon

IPC-9242: Guidelines for Microsection Evaluation

IPC-9691C: User Guide for the IPC-TM-650, Method 2.6.25 Conductive Anodic Filament (CAF) Resistance and Other Internal Electrochemical Migration Testing

IPC-A-630A: Acceptability Standard for Manufacture, Inspection, and Testing of Electronic Enclosures

IPC-4556A: Specification for Electroless Nickel/Electroless Palladium/ Immersion Gold (ENEPIG) Plating for Printed Boards

IPC-7527A: Requirements for Solder Paste Application

IPC-4204C: Flexible Metal-Clad Dielectrics for Use in Fabrication of Flexible Printed Boards

IPC-J-STD-002F: Solderability Tests for Component Leads, Terminations, Lugs, Terminals and Wires

IPC-4101F: Specifications for Base Materials for Rigid and Multilayer Printed Boards

IPC-1755B: Responsible Sourcing of Minerals Data Exchange Standard

IPC-2223F: Sectional Design Standard for Flexible/Rigid-Flexible Printed Boards

IPC-HDBK-9798A: Handbook and Guide to Supplement IPC-9797

IPC-WP-011: Guidance for Strain Gage Limits for Assemblies

J-STD-046A: Customer Notification Standard for Product/Process Changes by Electronic Product Suppliers

J-STD-048A: Notification Standard for Product Discontinuance

IPC-T-50P: Terms and Definitions for Interconnecting and Packaging Electronic Circuits

IPC-1401B: Corporate Social Responsibility Management System Standard

IPC -1751B: Generic Requirements for Declaration Process Management

IPC-6013F: Qualification and Performance Specification for Flexible/Rigid-Flexible Printed Boards

IPC-4413 - Am1: Specification for Finished Fabric Woven from Low Dk Glass for Printed Boards