This specification establishes the qualification and performance requirements for encapsulated discrete wire interconnection boards with wires that terminate in plated holes. 62 pages. Revised May 1990.
Products
This guideline describes flexibility and stretchability testing to evaluate printable electronics for stretchable and wearable applications. 26 pages. Released March 2017
IPC-6012E-AM1 is an Amendent to the IPC-6012E that clarifes the distinction between receding and dewetting solder in reflowed SPb or HASL coatings. The Amendment also provides amended criteria for minimum external conductor thickness of the finished printed board and new acceptance criteria for the minimum thickness of internal plated layers
IPC-6013D-AM1 is an amendment makes changes to the existing acceptance criteria for copper wrap plating measurements as defined by IPC-6013D. IPC-6013D-AM1 is an amendment which implements a dual criterion for Class 3 copper wrap plating, based on design effectivity (before and after July 01, 2018), so as not to impose onto legacy designs any additional qualification activity associated with...
Amendment 1 to IPC-7711/21C, the document provides procedures for removal and installation of D-Pak components
The IPC-6012FA Addendum, when required by procurement documentation/drawings, supplements or replaces specifically identified requirements of IPC-6012 revision F, for rigid printed boards that must survive the vibration and thermal cycling environments of electronic interconnects within the automotive industry.
The IPC-6012EA Addendum, when required by procurement documentation/drawings, supplements or replaces specifically identified requirements of IPC-6012 revision E, for rigid printed boards that must survive the vibration and thermal cycling environments of electronic interconnects within the automotive industry. The addendum includes updated requirements for lifted lands, pattern feature accuracy...
The IPC-6012FS space addendum provides exceptions to IPC Performance Class 3 requirements of the IPC-6012F for use in space and military avionics product. Exceptions include changes to acceptance criteria and/or sample size and test frequency for production lot acceptance testing. The IPC-6012FS covers requirements for rigid printed boards to survive vibration, extreme thermal cycling and ground...
IPC-A-600M-RL Redline document shows the changes from IPC-A-600K to IPC-A-600M in a side-by-side comparison of the two documents. The IPC-A-600M Redline is available in electronic format only. As a comparison document it does not replace the standard.
The IPC-6013EM Addendum, when required by procurement documentation/drawings, supplements or replaces specifically identified requirements of IPC-6013E, for flexible/rigid-flexible printed boards that must meet requirements to high reliability medical device applications. IPC-6013EM is the only global industry-consensus standard addendum for Medical Applications to Qualification and Performance...
The IPC-6012ES space addendum provides exceptions to Class 3 requirements of the IPC-6012E for use in space and military avionics product. Exceptions include changes to acceptance criteria and/or sample size and test frequency for production lot acceptance testing. The IPC-6012ES covers requirements for rigid printed boards to survive vibration, extreme thermal cycling and ground testing...
The IPC-6012EM Addendum, when required by procurement documentation/drawings, supplements or replaces specifically identified requirements of IPC-6012E, for rigid printed boards that must meet requirements to high reliability medical device applications. IPC-6012EM is the only global industry-consensus standard for Medical Applications to Qualification and Performance Specifications for Rigid...
Contains over 150 industry approved test techniques and procedures for chemical, mechanical, electrical, and environmental tests on all forms of printed boards and connectors. New and updated test methods are available for download at https://www.ipc.org/test-methods.
Covers the qualification and performance requirements of multilayer circuits used in hybrid packaging. These circuits consist of three or more layers of conductor patterns separated from each other by insulating materials and interconnected by a continuous metallic interlayer connection. The substrate may include passive elements. 66 pages. Released January 1987.
This document is designed to provide definitions for terms commonly used in the electronics industry. The definitions are intended to provide sufficient clarity of detail such that a reader utilizing English as a second language could understand the subtleties of the meaning. Revision P contains over 120 new or revised terms, including new terminology for back-drill structures, cable and wire...
IPC-6921 establishes and defines the qualification, performance, and acceptance requirements for wire bonding IC substrate products and flip chip IC substrate products. It provides photographs and illustrations of acceptable and defect conditions observed internally or externally on organic IC substrates, including requirements for critical IC substrate functional areas such as WB pads, SMT pads...
IPC-6012F Redline document shows the changes from IPC-6012E to IPC-6012F in a side-by-side comparison of the two documents. The IPC-6012F redline is available in both electronic and hardcopy format.
Tackling PCB cleanliness is a tough job; residues on printed circuit boards are directly related to the reliability of the produced hardware and can result in serious failures if not known or monitored. But how do you measure "cleanliness"? How clean is "clean"? The IPC-5701 provides guidance into how these issues should be approached and specified in purchasing documents, addressing levels of...
Every electronics manufacturer, whether an original equipment manufacturer (OEM) or electronics manufacturing services (EMS) company, must determine if the unpopulated printed boards entering the assembly process have an adequate level of cleanliness. The question of “how clean is clean enough?” is one that has no definitive answer, as there is no "golden number" for board cleanliness. The issue...
This standard is intended as a guideline in the proper preparation of a metallographic sample (microsection) of a printed board. The finished microsection is used for evaluating the quality of the laminate system and plated structures (e.g. PTHs and vias). Microsection sample preparation is regarded by many as a highly developed skill. The guidelines in this standard discuss the many variables and...
Defines a machine readable input format for Computer Numerical Control (CNC) drilling and routing machine tools used by the printed wiring board industry. The format may be used to transfer drilling and routing information between printed board designers, manufacturers and users or as the output CNC standard from converters that expand higher level design input such as IPC-D-350 data. Provides a...
This specification covers qualification and performance requirements of rigid mass laminated panels for use in multilayer printed boards. Testing procedures and criteria are addressed. 21 pages. Released July 1994.
Covers the materials, qualification, certification and performance requirements for multilayer polymer thick film (PTF) printed, extrusion deposited, or otherwise applied conductor, insulator and through-hole technology. This specification may also be used for procurement of single and double-sided boards. 59 pages. Released November 1989.
Describes the usage of libraries within the processing and generation of information files. The data contained within covers both the definition and usage of internal (existing within the information file) and external libraries. The libraries can be used to make generated data more compact and facilitate data exchange and archival. The subroutines within a library can be used one or more times...
Describes an intelligent, digital format for transfer of drawings between printed wiring board designers, manufacturers and customers. Also conveys additional requirements, guidelines and examples necessary to provide the data structures and concepts for drawing description in digital form. Supplements ANSI/IPC-D-350. Pertains to four basic types of drawings: master drawings, schematics, assembly...
Coming Soon
IPC-9242: Guidelines for Microsection Evaluation
IPC-A-630A: Acceptability Standard for Manufacture, Inspection, and Testing of Electronic Enclosures
IPC-7527A: Requirements for Solder Paste Application
IPC-4204C: Flexible Metal-Clad Dielectrics for Use in Fabrication of Flexible Printed Boards
IPC-J-STD-002F: Solderability Tests for Component Leads, Terminations, Lugs, Terminals and Wires
IPC-4101F: Specifications for Base Materials for Rigid and Multilayer Printed Boards
IPC-1755B: Responsible Sourcing of Minerals Data Exchange Standard
IPC-2223F: Sectional Design Standard for Flexible/Rigid-Flexible Printed Boards
IPC-HDBK-9798A: Handbook and Guide to Supplement IPC-9797
IPC-WP-011: Guidance for Strain Gage Limits for Assemblies
J-STD-048A: Notification Standard for Product Discontinuance
IPC-T-50P: Terms and Definitions for Interconnecting and Packaging Electronic Circuits
IPC-1401B: Corporate Social Responsibility Management System Standard
IPC -1751B: Generic Requirements for Declaration Process Management
IPC-6013F: Qualification and Performance Specification for Flexible/Rigid-Flexible Printed Boards
IPC-4413 - Am1: Specification for Finished Fabric Woven from Low Dk Glass for Printed Boards